How can the thickness and cross-sectional area of the inner gate ensure the ability to compensate for shrinkage in the LPDC gate structure design?
The sprue is a low-pressure casting shrinkage channel, and many people only focus on filling and ignore the solidification timing of the sprue; The gate solidifies too early, even if the cooling and exhaust are all qualified, the thick walled position still continues to shrink.
1、 Quantitative standards for gate cross-sectional area and thickness
The total cross-sectional area of the sprue is matched according to the weight of the casting, with an empirical range of 120-200mm ² for every 1kg of casting; The upper limit is set for thick walled components, and the lower limit is set for thin-walled shells.
Gate thickness: conventional 8-15mm; gate too thin, high filling resistance, fast solidification, short shrinkage window; The gate is too thick, resulting in a large amount of leftover material and high subsequent cutting costs. The gate itself forms a large shrinkage cavity.
The gate width should be as wide and thin as possible, with priority given to flat gates. The filling process should be smooth, and the area of the contraction channel should be large; Narrow and thick gates are prone to solidification at the center, while the surface is still flowing, causing shrinkage failure.
The transition fillet of the gate has a radius of R ≥ 3mm, and vortices and air pockets are generated at the sharp corners, resulting in porosity and stress concentration. At the same time, the root of the gate is prone to thermal cracking.
During the DFM review, Xinfeng Machinery synchronously calculates the solidification time of the sprue to ensure that the solidification time of the sprue is later than the solidification of the hot spot of the casting.
2、 Multi gate layout and gate position selection
Single gate is suitable for small, symmetrical castings with controllable filling flow direction; Multiple gates are suitable for large shells, and the convergence point of multiple streams of aluminum liquid is prone to air entrapment, so exhaust must be arranged at the convergence point.
The sprue should be prioritized near the thick hot spot of the casting, and nearby shrinkage should be compensated; The gate is placed at the far end of the thin wall, and the shrinking path is too long, resulting in significant loss of shrinking pressure transmission.
Ladder gate and gap gate are commonly used in new energy shells, with smooth filling and aluminum liquid rising layer by layer along the bottom of the mold cavity, reducing turbulent air entrainment.
The transition position between the gate and the casting body is reserved with cutting allowance to facilitate post-processing sawing and avoid cutting damage to the casting body.
3、 Differences in preference for gate solutions among overseas customers
Southeast Asian customers prioritize simple single gate, easy processing, convenient post-processing and cutting, and do not pursue extreme shrinkage. Slight shrinkage can be repaired by infiltration.
North American automotive pressure parts must submit a simulation report on gate solidification, with gate size and position solidification, zero tolerance for shrinkage defects, and infiltration cannot replace structural optimization.
European customers prefer flat sprues with gaps, stable laminar flow during filling, low risk of porosity, and the uniformity of internal structure in recast parts.
Middle Eastern construction machinery thick walled castings, with enlarged gate cross-sectional area to ensure shrinkage capacity, accept gate material weight deviation, and prioritize internal density.
4、 Defect chain caused by improper gate design
The cross-sectional area of the gate is too small and the thickness is too thin → the gate solidifies in advance → the shrinkage channel is closed → the hot spot shrinkage hole is loose;
There is no R at the sharp corner of the gate, resulting in air entrapment and hot cracks at the root of the gate;
There is no exhaust at the confluence of multiple gates → there are air holes and cold barriers at the confluence;
The gate is arranged in the thin-walled area → the filling distance is too long, the pressure transmission is insufficient, and the filling of the thick wall position is not in place.
5、 Long tail traffic layout ideas
Internal gating, shrinkage filling, and gap gating belong to the special topic of DFM filling, which is targeted at simulation engineers and mold designers.
keywords: LPDC gate design feeding shrinkage、low pressure casting ingate cross section calculation;
Category of questions: ingate thickness for aluminum LPDC casting;
Comparison class: Single gate vs Multiple gate for low pressure casting.
Suitable for filling simulation and gate scheme review pages.
6、 Common misconceptions in the industry
Misconception 1: The larger the sprue, the better the shrinkage. If the sprue is too thick, it will become a large hot spot, and the internal shrinkage of the sprue will extend to the casting after cutting.
Misconception 2: Placing the sprue randomly in a convenient processing location, away from the hot spot, excessively long filling path, and ineffective filling.
Misconception 3: Multi gate filling is faster, there is no exhaust at the confluence position, and it is easy to produce concentrated air holes due to gas entrapment.
FAQ
Q: Reference for gate cross-sectional area?
A: 120-200mm ² per 1kg casting.
Q: What is the thickness range for regular sprues?
A:8–15mm。
Q: What is the minimum requirement for the transition fillet of the gate?
A:R≥3mm, Anti roll and anti thermal cracking.
Q: What are the core timing objectives for gate design?
A: The solidification of the gate is later than the hot spot of the casting, maintaining the shrinkage channel.
Q: Advantages of Flat Gap Gate?
A: Smooth filling, laminar flow rising, and less entrainment.
Q: What is the priority location for pouring gates?
A: Close to the thick hot spot of the casting, make up for shrinkage nearby.
Q: North American pressure parts gate control?
A: Solidification simulation verification does not rely on infiltration to mask shrinkage cavities.
Q: What are the risk points of multiple gates?
A: The location of the aluminum liquid confluence is prone to air entrapment and must be equipped with exhaust.
Copyright © Zhejiang Xinfeng Machinery Co., Ltd. All Rights Reserved.